solar road stud,solar road marker,road pavement markers

There are several ways to effectively improve the compressive performance of solar road studs: one is to use PC bulletproof material for the exposed solar panels to enhance the compressive capacity of its electronic components; It is possible to use IC control to reduce the volume of the electronic circuit and reduce the pressure on the electronic components; the third is to design some reinforcing ribs on the shell to share the pressure on the electronic components.

The solar road stud is a high-tech “Jiao’an” technology product that is safe, environmentally friendly, low-carbon and energy-saving. It has the characteristics of high compressive strength, high wear resistance, no edges and corners, no fouling and 360¡ã reflection. It solves the problem of traditional plastics, aluminum alloys, etc. The reflective sheet-type protruding road signs are easy to break, poor sealing, easy to wear, easy to accumulate dirt, easy to fall off, short service life, high maintenance cost, and poor safety performance. It is a good guarantee for the safety of modern transportation.

The active lighting of solar road studs can not only avoid the interference of rain and fog to the greatest extent, but also free the driver’s sight from the dependence on the car lights, and the visual distance is farther and the effect is better. The most important waterproof part of the column-type solar double-sided six-lamp road stud is the LED lamp. If the sealing of his LED is not very good, then the LED lamp feet of the solar road stud are easy to get wet for a long time, and his lamp feet will slowly rust, and then pass through the rust after rusting, like the inside of the LED. Diffusion, and then the lamp beads do not light up, so the waterproof details of the column-type solar double-sided six-lamp road stud must be done well.

Solar road studs are powered by solar energy, and can work continuously for more than 48 hours on a single charge, with a service life of 3 to 5 years. The display mode flashes 120 times/min or is always on, and the display color is white, yellow, red, green and blue. The display device is ultra-bright LED, with 3 lamp beads on one side or two sides optional, more than 500m visual distance, working environment -40 ¡æ ~ +70 ¡æ. Die-casting aluminum shell + PC + ABS, the surface of the plastic sunroof is thickened with anti-skid treatment. Waterproof grade IP68.

Solar road studs have reliable quality and beautiful appearance, which can not only meet the technical standards of the industry, but also meet the growing aesthetic needs of people. The installation of solar road studs is not a complicated thing, but there are many details to pay attention to. These details play a very important role in ensuring the quality requirements and service life of road studs. If you need to purchase a large number of solar road studs, please contact Henan Ruichen Transportation Equipment.

Column-type solar road studs, double-sided six-light road studs, are one of the column-type solar road studs, also called solar road studs with feet, which are widely used in traffic safety facilities. The column-type solar road studs with double-sided six-light road studs are used to delineate the road in rainy, foggy weather and road bends. Solar road studs have played an important role in improving road safety and reducing traffic accidents.

The long-term stability of solar road studs is another important factor that determines the life of solar road studs. Therefore, the choice of batteries is very important. There are currently two types of batteries for solar road studs on the market for reference. One is that after 500 times of charging and discharging, the battery capacity is reduced to 50%; the other is that after 1,000 times of charging and discharging, the battery capacity is reduced to 79%.

Embedded solar road stud, as a kind of traffic product, uses sunlight to obtain energy and uses LED as light source. It has the advantages of energy saving, environmental protection and convenient installation. With the continuous increase in the number of cars, the requirements for humanized signs and warnings in road design are constantly increasing. For the use of mains power supply to warn that the cost is too high, the use of solar road studs and solar signs will be the most important. origin of. In developed countries abroad, the habit of looking at the markings during the day and the “road studs” at night has long been formed.

¡¾Solar Road Spike¡¿- This solar road stud can automatically absorb free solar electricity during the day and illuminate at night or in bad weather. After fully charged, the light can work continuously for more than 72 hours. The button at the bottom is the (on/off) switch function, which can solve the problem of power consumption during long-term transportation and storage. ¡¾Waterproof Solar Road Spike¡¿ – The solar road stud is IP68 and 100% waterproof for long time outdoor use. Cope with bad weather such as rainy days and hot weather. No rust, no leakage, durable.

The 360-degree cat-eye road studs are curved and can be seen from any angle. And the CAT EYE design can focus the light 360 degrees; there are 6 super bright LED lights, which can attract the line of sight from more than 800 meters away. A solar-powered spotlight with high-efficiency solar panels, so no AC or DC power is required. And through a specific light control system, the LEDs only light up in a dark environment (at night) and automatically charge during the day (full sunlight). Our products are made of eco-friendly materials and waterproof (>IP67), it doesn’t matter even if you put them in water for a long time. It can be widely used for lighting and decoration of roads, courtyards, gardens, pools, etc.

The solar road studs are IP68 waterproof and can withstand any harsh weather such as storms or blizzards. Solar road studs can effectively isolate water and fog. The visibility of the solar road stud is more than 800 m, it can effectively provide night lighting. Classic design fits a variety of landscapes and styles and is suitable for night lighting driveway dock deck path boat bridge driveway garden yard or patio. The solar road studs are easy to install, when you use it for the first time, please turn on the light switch at the bottom, then charge it in the sun for 1-2 days. Finally install with screws or construction adhesive.

Solar road studs excellent lighting and easy installation: 6 high-grade LED beads (about 40 lumens), providing super bright light and more than 800 meters of visible distance, such as decks, roads, docks, oceans, paths, driveways, gardens, stairs, steps , walkways, etc. Right out of the box, just flip the switch and fasten with the screws provided! IP68 Waterproof & Ultra Durable: With an IP68 waterproof design and a tightly sealed battery compartment, this solar light can withstand any dreadful weather like storms or everyday hot.

The high quality aluminum alloy housing of solar road studs effectively prevents these outdoor solar LED deck lights from rusting and can withstand up to 3 tons without worrying about cars and children stepping on them. Solar spikes for fast charging and long-lasting lighting: Adopt advanced monocrystalline silicon solar panels and large-capacity batteries (600mAh). Our driveway lights support lighting from dusk to dawn after a full charge of 4-5 hours. Without manual control, these lights automatically turn on at dusk and turn off at dawn.

The embedded solar road stud has a beautiful appearance and can be used for road induction and decoration. The streamlined design, the frequency of LED lighting can be selected, and the use scene can be selected flexibly. The lamp holder is made of die-cast aluminum material, and the surface is sprayed with plastic, which is light in weight, waterproof, shock-resistant and corrosion-resistant. Using thickened pc material, it has particularly good impact strength, UV resistance, thermal stability and flame retardancy.

Solar road studs: 1. Good compressive ability. The solar road stud can withstand the impact from the vehicle tires 2. Strong reflective ability: the reflector creates a diamond-like effect, which is very attractive under the light, and the driver can feel the reflection at a distance of 500m, so it is helpful for night driving, reducing Accident happens. 3. Solar road studs can be easily applied. 4. Anti-corrosion of solar road studs: water resistance, oil resistance, chemical resistance

The sealing performance of solar road studs If the solar road stud is not completely sealed, water will seep, which will cause a short circuit in the circuit, and the consequences will be catastrophic. Therefore, a qualified solar road stud, its sealing performance must pass the test. Solar road studs should be able to actively emit light and outline the outline and edges of the road to the greatest extent, which is one of the most important features compared to ordinary reflective road studs. In this indicator requirement, the requirement of the relevant standards of the Ministry of Transport is 2000MCD.

The high-strength material on the top of the solar road stud has good light transmission performance and compression resistance. The biggest advantage of solar road studs and ordinary road studs of Henan Ruichen Traffic Equipment Co., Ltd. is that they have strong compressive ability, are embedded in the road surface, beautifully installed, can be used in the middle of the road without being crushed, and have a long service life.

Solar Road Stud Installation Instructions: Road Side Line. Solar road stud installation steps: 1. Positioning: first use a ruler to determine the installation position, ensure that each position is longitudinally in a straight line, the installation distance is subject to the design requirements, and the installation place should be flat, dry, clean, and without gaps. 2. Mixing glue: road stud A glue, road stud B glue, the ratio of A glue B glue is 1:1. The glue must be mixed evenly and the color is consistent. 3. Glue: The road surface should be cleaned during installation, and the glue should be moderate. It should not only stick to the bottom surface of the road stud, but also not overflow too much. About 40-50 grams of glue should be used for each road stud, and the glue should be applied to the bottom of the road sign. in the pre-marked position. After installation, clean the road debris. 5. Inspection: The installed road studs should be inspected after two hours.

High-quality and durable solar road studs: beautiful appearance, the main body is made of flame retardant PC/ABS plastic; the transparent body is made of transparent polycarbonate with good light transmittance; the sealant is made of modified silicone resin. Dust-proof and waterproof solar road studs: energy saving and environmental protection, low power consumption, long life, double-sided lighting induction standard power is only 0.45W. The waterproof and dustproof design keeps out dust and water for extended durability. Application of solar road studs: Pavement signs are mainly installed on highways, tunnels, shoulders, roundabouts, curbs of safety islands, entrances and exits of underground parking lots or walls of tunnels and side walls of roads.

Solar road stud solar LED street light: The active light-emitting part adopts high-brightness LED light source, with uniform illumination, soft light, no glare, and good stability. The passive light-emitting part adopts ultra-high-intensity reflective film, which can reflect the car lights well in the event of a power failure. The effect of solar road studs is good: this emergency reflector has a strong warning effect, and the visual distance can reach more than 800 meters. Equipped with voltage regulator and anti-jamming chip, safe and practical, low failure rate and easy installation.

The solar road stud has 6 super bright white LEDs. Solar Spotlight with High Efficiency Solar Panels: No AC or DC power required. Environmentally friendly products with high energy conversion rate. A specific light control system ensures that the LEDs only light up in dark environments (at night). Solar road studs automatically charge during the day (in full sun) and light up at night. Easy installation and adjustable lighting angle. The waterproof grade of solar road studs is IP68, which can be placed in water for a long time. Dust-proof, can be used for road lighting or garden decoration. Can be widely used in roads, courtyards, gardens, swimming pools, etc.

Features of solar road studs: 1. Cast aluminum shell, surface polishing and oil injection, exquisite and beautiful appearance. 2. The surface of the solar panel has a non-slip design to ensure that it will not be scratched, thereby ensuring the photoelectric conversion efficiency of the solar panel; 3. This product uses capacitors as energy storage components to ensure the service life and performance of the product. 4. Single-sided or double-sided optional solar road studs;

Compressive performance If the solar road stud cannot withstand a certain pressure, it will not work properly after being crushed or impacted by a car. Therefore, compressive resistance should be the most basic condition for the normal operation of the solar road stud. The solar road stud itself is an electronic product. It is very difficult for its electronic components to have high compressive performance. Therefore, in general, the compressive performance of solar road studs is worse than that of ordinary road studs. Some. At present, according to the requirements of the relevant technical standards of the Ministry of Transport, the compressive index of solar road studs must reach 10 tons.

Solar Road Studs ¡¾Automatic Charging¡¿Solar driveway lights absorb unrestricted solar energy for about 6-8 hours and can last for 72 hours. Automatically recharges during the day and lights up at night when it falls down or in bad weather. Not only is it eco-friendly, it saves money, and the continuous solar power works for you. Thank you for helping the earth! Solar road studs IP68 waterproof: This outdoor step light is certified IP68 and 100% waterproof, and the sealed battery box can withstand most environments such as heavy rain and foggy weather. No rust, durable all year round.Hard Shell: Made of high-quality polycarbonate, it will not damage the outdoor solar street light even if the car or truck is running, it can withstand 20 tons (4200 lbs) of pressure, suitable for any road. Each light has 6 high quality LED lights that emit a visible ultra-bright and steady light over 875 yards (about 100.6 meters).

Solar road studs can be divided into embedded type and raised type according to the different installation positions. The raised road studs can only be installed on the edge of the road due to the compressive performance. On the ground, the exposed surface is only about 5 mm. The mechanical analysis is almost flat with the ground, and it has a very strong anti-rolling ability, so the solar road stud can be installed on the center line of the road.

Solar road studs are intelligent road studs that can be actively illuminated by Henan Ruichen Traffic Equipment Co., Ltd. Smart solar road studs are called pedestrian crossings, also known as luminous zebra crossings, zebra crossing road studs, and smart zebra crossings. They are generally installed at one end of the zebra crossing. The solar road studs emit warning lights through LEDs to warn drivers to slow down or stop and wait, and at the same time remind pedestrians to pay attention to the intersection. vehicles to improve the safety of pedestrians crossing the road.

¡¾Solar road studs high quality¡¿- This solar road stud adopts thick aluminum casing and good sealing process, it has UV protection, anti-rust and working temperature: -20¡æ to 70¡æ. It can carry loads of up to 400 pounds (up to 20 tons), pass cars and trucks safely without damage, and work as usual. ¡¾Solar Road Studs Wide Light Area and Easy Installation¡¿- A single solar light can light an area of ??875 yards, the orange light color is very bright. Drive out the darkness and ensure safety at night. The screws need to be secured to the ground to complete the assembly. ¡¾Multiple uses of solar road studs¡¿-Wireless setup and operation. This solar dock light can be used on roads, paths, decks, docks, driveways, gardens, walkways, sidewalks, garage paths, stairs and more.

Solar road stud installation location: 1. Dangerous dead corners and sharp bends, black spots and areas with insufficient light. 2. Areas with unpredictable weather conditions (coastal roads, foggy areas, wet and rainy areas, etc.). 3. Solar road studs Union intersections, up and down ramps, centerlines and dividers, entrance warnings, carpool lanes, bridges, intersections and sidewalks 4, guide lines, traffic islands, roundabouts, mountain roads. 5. Airport taxiways, bicycle and sidewalks, ships and boats. 6. Solar road stud entertainment area, parking lot, hotel entrance, gas station, etc.

Solar road studs – every morning and evening rush hour and holidays, a large number of motor vehicles and pedestrians will gather here, the traffic flow is large, the pedestrians are many, and the traffic safety is hidden. After many field investigations on the Beishan section of Dalian Street in the jurisdiction, it was decided to use the smart zebra crossing solar road studs of Henan Ruichen Transportation Equipment Co., Ltd. to solve this problem. The road stud lights on both sides of the “Smart Zebra Crossing” can show two colors of red and green as the signal lights change. When the light is green, the road stud is flashing green; when the light is red, the road stud switches to red. In the past, the warning function of solar road studs for pedestrians was mainly at night, while the road studs used in Yangquan have high brightness, which is another major feature of the product. Even in the daytime, drivers 50 meters away can clearly find them.

Compared with ordinary reflective road studs, solar road studs have two most important characteristics: they are brighter. The reflective brightness of ordinary reflective road studs is only 300MCD to 400MCD, while the luminous brightness of solar road studs can reach 2000MCD, which is 6 to 7 times that of the former. Such high-intensity light can penetrate rain and fog at night, and the solar road studs guide the driver safely and effectively.

There are two types of solar road studs in Henan Ruichen: one is for the driver to see, the light of this road stud should be directed towards the distance of the road, and the driver needs to be able to find the solar road stud at the intersection 200 meters away, and the brightness should be high; The other is for pedestrians. The light of road studs should be upward. When pedestrians walk to the intersection, the road studs are the most conspicuous, and the light should be soft and comfortable.

The life of the solar channel battery should not only be long enough, but also be able to work normally in a wide temperature range. The material inside the battery is a chemical substance. If the temperature is too high or too low, it will not work properly. Therefore, its working temperature range must meet the requirements of the actual use environment. The requirements of the relevant standards of the Ministry of Transport for this indicator are that the solar road studs must work normally within the range of -10¡ãC to 50¡ãC. In fact, the ambient temperature of solar road studs often exceeds this range, which requires more reliable and higher performance batteries to make solar road studs.

The solar road stud is a kind of uniform light road stud for pedestrians. The uniform light road stud is round in shape, which looks more like the traffic light on the opposite side, and is pulled to the sole of the foot. The reminder of solar road studs is really warm. In the future, I will no longer be a bower and cross the road safely. With such a smart crosswalk, I can see the zebra crossing more clearly at night! There are also clear reminders for drivers and pedestrians, which is great!

Solar road stud lights, also known as solar cast aluminum road lights, reflective markers, LED road stud lights, etc., are charged by solar panels, stored in the battery, and automatically illuminated at night and when there is insufficient light in rainy and foggy weather, which can guide the vehicle correctly. Driving direction, effectively guaranteeing traffic safety. Solar road stud lights, also known as solar cast aluminum road lights, reflective markers, LED road stud lights, etc., use solar energy to charge, automatically emit light at night and when there is insufficient light in rainy and foggy weather, guide the vehicle in the correct direction, and effectively ensure traffic safety. .

The embedded solar road studs cause great damage to the road surface, and the capacitive solar road studs are too expensive. Therefore, the most widely used solar road studs in the industry are the raised battery solar road studs. In the following, the author takes the raised battery solar road stud as an example to discuss the performance, existing problems and future development trend of my country’s solar road stud products. There are various forms of solar road studs, and the installation positions are also different. No matter what kind of solar road stud, considering its basic characteristics should start from the following aspects.

According to the different installation positions, solar road studs can be divided into embedded type and protruding type. Because the solar road studs installed on the road centerline have particularly high requirements on the compressive performance, the former is generally used in the road centerline, and the latter is mostly used in the road edge line. According to the different energy storage elements, solar road studs can be divided into two types: capacitive type and battery type. The service life of the former can reach five to seven years, and the service life of the latter generally ranges from one to three years.

Solar road stud is a new type of active luminous warning product for road traffic facilities. The written language is solar protruding road signs. It uses solar panels as charging components, batteries or capacitors as energy storage components, and uses LEDs combined with reflectors to emit light. The solar road stud lamp uses solar energy to charge, automatically emits light at night and when the light is insufficient in rainy and foggy weather, outlines the outline of the road, guides the vehicle in the correct direction, and effectively guarantees traffic safety.

There is one part of the solar spike that needs attention, and that is its solar panels. The solar panel directly absorbs the solar energy and converts the light energy into electrical energy, which is the first link in the whole solar road stud working system, and its working efficiency directly determines the quality of the solar road stud. At present, the solar cells commonly used in the industry are monocrystalline silicon panels. This is because monocrystalline silicon solar panels have a high photoelectric conversion rate of about 14%, which can convert solar energy into electrical energy to the greatest extent possible to ensure solar road spikes. Energy supply at work. In addition, solar panels must be high-hardness, wear-resistant circuit boards. If the strength is not enough, it will be crushed and worn by the wheels every day, and it is easy to grind, which will affect the conversion efficiency of solar panels.

More than 20 solar road studs are installed on both sides of the pedestrian crossing. The principle of this safety warning system is to automatically detect the direction and position of pedestrians crossing the street through thermal imaging video detection at the pedestrian crossing in the road section, triggering the LED road studs on the ground to flash, and the solar energy Road studs warn passing vehicles to give way to pedestrians to ensure safe travel at night.

Solar Road Stud is a prominent sign. Self-luminous, powered by solar panels, durable Ni-MH batteries. It is generally used for paving, and is used at night or in rainy and foggy weather to outline the outline of the road and improve road safety. The Solar Road Stud weighs at least 30 tons, has a stable working time of at least 15 days after a full charge, 3 years warranty and optional colors are available. It is now the first choice for traffic safety. If you need solar road studs, please contact Henan Ruichen Traffic Equipment Co., Ltd.

Working principle of solar road studs: The working principle of solar road studs can be briefly summarized as follows: During the daytime, solar panels absorb sunlight, convert solar energy into electrical energy, and store it in energy storage devices (batteries or capacitors). At night, the electrical energy in the energy storage device is automatically converted into light energy (controlled by a photoelectric switch), and the LED emits bright light to outline the outline of the road and induce the driver’s sight.

It is very safe for solar road studs to meet the national standards. The national standard solar road studs can bear less than 25 tons of pressure, and after damage, the glass road studs become obtuse-angled particles with a diameter of less than 4 cm. The quality of Ruichen’s solar road studs is feasible and resistant to pressure. Can be up to 40 tons or more. Solar road studs have the characteristics of high pressure resistance, high wear resistance, no fouling and 360¡ã reflection. They are the choice of warning signs for safe driving of vehicles, and also mark a beautiful safety line for pedestrians.

Solar road studs multifunctional: white solar base light, suitable for roads, paths, decks, docks, driveways, gardens, walkways, sidewalks, courtyards, etc. This pedestal light can be quickly installed on the ground where it can absorb direct sunlight. With its cordless design, the solar road stud allows you to fasten it with screws or glue so you can secure this street light on the road, so you don’t need to buy new screws. Solar Road Studs Note: Prolonged exposure to wet areas may reduce the lifespan of these solar deck lights. Since it may run out during prolonged shipping, we recommend about 3-5 days of test use before securing it to the ground.

Solar spikes come with solar panels and rechargeable batteries. No wiring required, no electricity bills. Strong and durable, the static pressure exceeds 20 tons, which means it will work even if a car or truck runs over it. Two-year warranty. Solar road stud intelligent light sensing function, automatically turn off and start charging at dawn, and automatically illuminate at dusk. Provides up to 24 hours of lighting when fully charged. Each solar deck light features 6 high-brightness LED lights for an eye-catching glow in dark or foggy days.

Advantages of solar road studs: 1. Aluminum outer casting with anodized coating. The anodized coating of the case protects it from oxidation and looks smooth and beautiful. 2. The solar road stud reflector is embedded from the inside. The reflector is embedded from the inside and is lower than the surrounding aluminum material, which is not easy to be damaged. The interior of the reflector is coated with a thin film to avoid corrosion of the reflector. Effectively prolong the service life of the reflector.

The solar road stud is a safe and green transportation solar energy product. During the daytime, the solar panel absorbs the sunlight, converts the solar energy into electricity, and stores it in the energy storage device (battery). At night, the electrical energy in the energy storage device is automatically converted into light energy (controlled by a light-controlled switch) and flashes in the dark night. In dark nights, rainy days, foggy days and other poor driving visibility, if the vehicle deviates from the lane and presses on the solar road stud, the driver can also detect the sound and bump in time, causing alertness. Solar road studs will automatically flash and emit light when there is insufficient light at night. Usually, solar road studs have active lighting and passive lighting. Even if the solar road stud is broken, it can remind the driver to drive safely, outline the road outline and guide the road.

The first solar road stud: the luminous brightness is large. The reflective brightness of ordinary reflective road studs is only 300MCD to 400MCD, while the luminous brightness of column-type solar double-sided six-lamp road studs can reach 2000MCD, which is 6 to 7 times that of the former. Such high-intensity light can penetrate rain and fog at night, safely and effectively guiding the driver. Second: Active light, dynamic warning. The solar road stud flashes at a certain frequency at night, and its dynamic warning effect is very strong.

Solar Road Studs Dual Color and Double Surprise: 2 colors in 1 (cool white or warm white), so that solar road studs can not only be used as driveway marking lights, warning desk lights and guide lights, but also can be used as solar outdoor decorative lights to beautify your House, garden and terrace. The two-color pattern of solar road studs is perfectly suitable for different decorative styles! If you have any needs, please contact Henan Ruichen Transportation Equipment Co., Ltd., we are a factory specializing in the production of solar road studs.

Compared with ordinary reflective road studs, solar road studs have two most important features: active lighting and dynamic warning. The solar road stud flashes at a certain frequency at night, and its dynamic warning effect is very strong. Active lighting can not only avoid the interference of rain and fog to the greatest extent, but also free the driver’s line of sight from the dependence on car lights, and the visual distance is farther and the effect is better.

Advantages of solar road studs: 1. High quality adhesive We fill solar road studs with AB epoxy adhesive, which is firm inside, high waterproof performance, IP68 protection rod, can resist 30 tons of pressure, widely used in swimming pools. 2. The super bright led LED is very bright, visible from 1000 meters, with a service life of up to 100,000 hours, and will not fade or disappear during use. 3. Reduce impact. The smooth-edged aluminum frame of the solar road studs is sandblasted, and the solar road studs are harmless to the tire and prolong the life of the wheel.